Skip to content
Back to Blog
Engineering·5 min min read

Display brightness in nits explained: indoor, window, outdoor

What nits and cd/m² mean, which brightness suits indoor spaces, shop windows and outdoor sites, and why a light sensor matters more than the highest number.

s
smartenic Redaktion
Display brightness in nits explained: indoor, window, outdoor

Every data sheet lists a brightness value, usually in cd/m², sometimes in nits. What the number means only becomes clear on site: a screen that looks pleasant in a lobby is barely visible behind a sunny shop window. This article explains what brightness means for displays, which values are typical indoors, in shop windows and outdoors, and why more is not automatically better.

What do nits and cd/m² mean?

Nits and cd/m² are two names for the same unit: candela per square metre, the luminous intensity a screen emits per area. A display with 3000 cd/m² is ten times as bright as one with 300 cd/m². The data sheet figure is the maximum brightness on a white image, not the level the device runs at all the time.

What matters when comparing:

  • Same unit: 3000 nits and 3000 cd/m² are identical.
  • Maximum value: in operation, brightness is often turned down, especially in the evening.
  • Contrast counts too: a bright screen that strongly reflects ambient light still looks washed out.

How bright does an indoor display need to be?

Indoors without direct sunlight, the brightness of a normal professional display is enough. According to their data sheets, the SMARTENIC Tower Indoor kiosk and the SMARTENIC Vision Indoor wall display have 300 cd/m². That is easy to read in lobbies, sales floors, waiting areas and offices, and does not dazzle when people step close.

More brightness would be a drawback indoors. A very bright screen in a softly lit room looks glaring, draws more power and produces more heat. Indoors, focus on these points instead:

  • No direct sunlight on the screen, not even at certain times of day.
  • No strong spotlights reflecting in the glass.
  • Avoid windows behind the viewer, or the bright window area will reflect.

For most locations inside a building, an indoor kiosk such as the SMARTENIC Tower Indoor is therefore the right choice.

Why does a shop window need so much more brightness?

A shop window needs far more brightness because the screen competes with daylight in the street. Passers-by look from the bright outdoors at a pane that also reflects. A display with indoor brightness is then hard to make out. Shop window displays are therefore built for many times that brightness.

The values at smartenic:

  • SMARTENIC Vision HB: 3000 cd/m², single-sided, facing the street.
  • SMARTENIC Vision HB Dual: 3000 cd/m² to the street and 700 cd/m² on the inside. The inside is deliberately dimmer because it addresses customers in the shop and should not dazzle them.

Both devices adjust brightness automatically with a light sensor. At midday with sun on the glass the display runs bright; in the evening it dims. This keeps the picture readable, saves power and stops the window looking glaring at night. More on our shop window display page.

How bright do outdoor displays need to be?

Outdoor displays stand in direct daylight and need a similar order of brightness to shop window displays, plus a housing that withstands weather and temperature. Depending on size, smartenic outdoor devices have 1500, 2500 or 3000 cd/m², IP65 protection and tempered glass.

  • SMARTENIC Vision Outdoor (wall display): 21.5 inches at 1500 cd/m², 32 to 55 inches at 2500 cd/m², 65 to 98 inches at 3000 cd/m².
  • SMARTENIC Tower Outdoor (kiosk): 32 to 55 inches at 2500 cd/m², 65 to 98 inches at 3000 cd/m².

Both adjust brightness via a light sensor. Our outdoor digital signage page gives an overview.

What affects readability besides brightness?

Besides brightness, a display's readability depends on contrast, reflections, viewing angle and content. A screen with a high brightness rating showing light text on a light background stays hard to read. Conversely, well-designed content gets more out of any device.

Check these factors:

  1. Orientation: if the window faces south or west, the sun hits the glass directly at certain times. Design content for those hours with extra contrast.
  2. Reflections: bright facades opposite, cars or awnings reflect in the glass. A small gap between display and glass and the right height help.
  3. Viewing angle: smartenic shop window displays use IPS panels with wide viewing angles, so the picture stays visible from the side.
  4. Design: large type, strong colours and dark backgrounds with light text read better behind glass than thin lines and pastel shades.

How do you check brightness before buying?

The best way to check brightness before buying is at the real location and at the least favourable time of day. A data sheet value tells you what a device can do, not how your window looks at three in the afternoon in June. If you know that situation, you choose the right format with more confidence.

  1. Watch the sun: note when sunlight falls directly on the glass or the planned spot.
  2. Photograph reflections: take a photo into the window from outside. What you see is what passers-by see.
  3. Consider the content: check whether your content is designed mainly dark or light.
  4. Set operating hours: when should the display run, and when can it be off?

Is more brightness always better?

More brightness is only better where strong ambient light works against the screen. Indoors, a screen that is too bright causes glare, higher power consumption and more heat. The right brightness is the one that suits the location, combined with automatic control that adapts to the time of day.

A simple guide:

  • Indoors without direct sun: indoor kiosk or wall display with indoor brightness.
  • Behind a shop window: high-brightness display with a light sensor, single or double-sided.
  • Outdoors: outdoor device with high brightness, IP65 and suitable cooling.
  • Large areas beyond single displays: LED wall, planned per project.

What is the next step?

Photograph the planned location at the brightest time of day and note which direction the window faces. With that, we recommend the device with the right brightness. Standard delivery time is 12 to 16 weeks from order; selected sizes are available from stock.

smartenic advises, delivers and installs in Austria and Slovakia. Send us photos and your questions via the contact form.

Frequently asked questions

Technically yes, but it rarely makes sense. A TV is built for living rooms; its brightness is usually not enough against daylight behind glass, and it is not designed for long daily operating hours. Behind the glass, heat from sunlight adds to the load. Shop window displays are built for exactly these conditions.

Yes. At full brightness, a high-brightness display needs considerably more power than an indoor display of the same size. Automatic brightness control reduces consumption, because the device only turns up in strong ambient light. A schedule that switches the display off after closing time saves more.

Shop window displays are built for this situation. The Vision HB and Vision HB Dual use industrial panels with an aluminium heat sink and, according to their data sheets, are rated for operating temperatures up to 50 °C. There should still be enough air around the device; a fully sealed display case with no air exchange is not ideal.

Because the inside addresses customers in the shop who look in indoor light and from a short distance. At full window brightness it would dazzle them. 700 cd/m² is well above a normal indoor display and stays readable even when daylight falls into the shop through the window.

Not with smartenic shop window and outdoor devices. A light sensor measures ambient light and turns the screen up or down automatically. During commissioning we tune the control to the location. Indoor devices run at a fixed brightness that can be adjusted if needed.
s
Written by
smartenic Redaktion
Share:

Interested in our solutions?

Explore our products and case studies or get in touch to discuss your project.